1. Quality inspection of water purifiers in 2017: 38 batches of water purifiers such as Philips failed to pump
On the 12th, the General Administration of Quality Supervision, Inspection and Quarantine issued a special spot check on the national supervision of water purifier product quality in 2017. A total of 109 batches of products produced by 107 companies in nine provinces (cities) such as Beijing were sampled. After inspection, 71 batches of products produced by 69 companies were qualified, 38 batches of products produced by 38 companies were unqualified, and the rate of detection of unqualified products was 34.9%.
In terms of the size of the company, large, medium, and small companies that randomly sampled accounted for 26.2%, 19.6%, and 54.2%, respectively, of the total number of sampled enterprises. The pass rates for spot checks were 89.7%, 66.7%, and 52.5%, respectively.
The results showed that 38 batches of products such as Philips failed. Five companies such as Rongsheng Electric failed to qualify for two consecutive national pumping tests.
2017 Water Purifier Product Quality National Supervision Special Spot Inspection Unqualified Products and List of Manufacturers
Water Purifier Product Quality Supervision and Inspection
The main quality issues:
(1) The health and safety of the whole machine does not meet the standard requirements. There were 35 batches of products that failed the project. The main reason was that some of the production enterprises used water-contact materials and components that did not meet the standards for hygiene and safety. The product manual lacked key information such as the time and amount of water flushing.
(2) The total net amount of water does not meet the standard requirements. There were 9 batches of products that were unqualified, mainly due to the fact that some production companies used low-quality water treatment cartridges, resulting in water quality of the water purifiers and pollutants (contaminated water) within the company's total net water volume. Removal of organic matter, microorganisms, etc. is not satisfactory.
(3) The power cord connection and external cords do not meet the standard requirements. There are six batches of products that failed the project, mainly because the cross-sectional area of ​​the power cords used by some manufacturers did not meet the standard requirements. Overloading for a long period of time will lead to heat generation of the fuselage, aging and cracking of the insulation skin, and potential accidents such as electric leakage.
(4) The input power and current do not meet the standard requirements. There are two batches of products that failed the project, mainly due to the nominal power of the products of some manufacturers. If the capacity of the power socket used by consumers is too small, the capacity of the socket cannot meet the requirements for use, and it will cause overload and other overload phenomena.
2, iPhone X "fatal defect" exposure! Duanzi hands busy all day
At the product launch conference held on Tuesday, Apple introduced new iPhones, third-generation Apple Watch smart phones that can make calls, and new Apple TV set-top boxes. But for the diehard “fruit powderâ€, it is disappointing that the iPhone X will not begin shipping until November 3, much later than the September 22 of the iPhone 8.
At the same time, the domestic legmen began to work hard and laughed and sprayed:
"Small series, I want to complain! My wife lied to me!"
When sleeping, you can choose to wear a cap or sunglasses
So there is a question, what if someone looks like me?
3, Shenzhen Stock Exchange sent a letter asking LeTV: Why pay back the money to Jia Yueting
On September 12, the Management Department of the Shenzhen Stock Exchange's Growth Enterprise Board issued a letter of concern to LeTV. It stated that it was highly concerned with Jia Yueting’s commitment to reduce its capital and asked LeTV and Jia Yueting to explain the relevant issues.
According to the letter, according to LeTV's Announcement on the Special Disclosure of Commitments, issued on July 27, 2015, and the Announcement on the Specific Disclosure of Commitments issued on October 30, 2015, Jia Yueting promised to reduce its holdings. The funds were all loaned to the listed company. Within six months from the date of receipt of the repayment of the listed company, Jia Yueting used the repayment proceeds to increase the holding of LeTV.com shares. The company's 2017 semi-annual report shows that the company has returned all loans to Jia Yueting.
The Management Department of the Shenzhen Stock Exchange's Growth Enterprise Management Company requested LeTV.com to specify the time, amount, and repayment reason for Jia Yueting’s repayment, and whether Jia Yueting had any violation of the promise and explained the reasons, and asked LeTV.com’s sponsor agencies and lawyers to express their opinions. .
You can look for top sell Key Chain here.Our factory is located in Guangzhou, China's "leather capital", which will be more affordable in terms of the price of goods.
We employ the most creative designers and tech brilliant engineers to make the best cases. We believe our high-quality products with competitive prices will satisfy your needs.
The productive process :
Make the Products Mould –Cutting the fabric –Do the half products – Finish products – Cleaning –QC- Package – Shippment .
For Key Chain,High quality Key Chain,hot selling Key Chain,custom Key Chain
Ysure Leather case 24/7 Support : 86 13430343455 , https://www.ysurecase.com